Recent Posts

1

Drive train, fuel, suspension, steering & brakes / Re: Head Gasket Issues

« Last post by colin evans on Today at 11:39:48 »

Thanks, just taken the head and inlet manifold to the machine shop for pressure testing. Fingers crossed.
Can anyone tell me the torque setting for the smaller head bolts at the front (2 external and 2 in chain aperture)?
Thanks

2

Drive train, fuel, suspension, steering & brakes / Re: M127 Head Gasket

« Last post by Duncan200 on Today at 09:09:14 »

Just to update you all, I spoke to Mike at Metric via email. Very helpful.

Ordered the part number he suggested and it fits.

One thing interesting to note is the part number he suggested (Elring 046.451) is exactly the same part that I already had.

It was like the whole gasket was cut too far forward as it was definitely overlapping the pistons on the trailing edge.

Anyway, head is on, all good.

Thanks Doug

3

Wanted To Buy / Re: Looking for manual transmission for 1965 230sl

« Last post by stickandrudderman on Today at 08:56:13 »

I have a rebuilt one but I'm in the UK.

4

W11x chassis cars / Re: 1961 220Sb stalls when choke is pushed in.

« Last post by ja17 on Today at 05:46:51 »

Good job Brad,
Find some ethanol-free gasoline to put in it before you store it for the winter this fall to prevent more problems. You can go back to running your ethanol gas the rest of the time.

5

Drive train, fuel, suspension, steering & brakes / Re: Power Steering Leak

« Last post by Cees Klumper on Today at 02:30:03 »

No need to open a 'bleed nipple', the bleeding is done as per Benz Dr Dan's instructions. But, you appear to have a leaking steering box. First time I can remember in the past 22 years on this forum! You may want to call around to a couple of the parts suppliers for a rebuild kit, I reckon they don't get this request very often.

6

Drive train, fuel, suspension, steering & brakes / Is front inner bearing retainer nessesary

« Last post by erickmarciano on Today at 02:23:37 »

Hi guys, I’m in the process of changing my front rotors so I decided to clean the hubs and grease
On one side, I have a retainer for the bearing behind the seal and none on the other side. I reassembled the one that doesn’t have it, and I only realized when I cleaned the other side that it was missing .
Is this part important ? I would think not since it’s all squeezed in ??its called a puller ring
Pn 1113340064
Number 38

7

Drive train, fuel, suspension, steering & brakes / Re: Power Steering Leak

« Last post by acbrock on Today at 01:11:22 »

Arggg.  Well I could not get the damn bleed nipple to turn.  But while turning the wheels and watching all the bubbles come out I realize the bleeding would not matter.  I am leaking from the spot in the picture.  I will dive in to what this is and see if it is something I can replace or need to take in.  I hope I can do it.  I am guess it it is A,B and C in that drawing in the tech manual.  Anyone know that gasket I am going to need to get?
Oof reading more if that is it then I dont think I can do it unless I get a torque gauge...

8

Drive train, fuel, suspension, steering & brakes / Re: Power Steering Leak

« Last post by Benz Dr. on June 02, 2024, 22:24:28 »

Raise the front of your car until the wheels are off the ground.  Turn your steering wheel back and forth and keep adding ATF as the fluid goes down in the canister. Do NOT run your engine or the fluid will foam up.

Once you quit seeing air bubbles in the fluid, turn your steering wheel full lock in both directions which should produce a few more bubble. Fill to the line on your canister housing only when you're sure all of the air has been purged out. This method is, by far, the best way to do this.

9

Drive train, fuel, suspension, steering & brakes / Re: Correct Dipstick?

« Last post by acbrock on June 02, 2024, 22:19:27 »

Cool I will look around for those.
Looks like my Engine is 127 981 12 002690
So probably the A 127 010 03 72
or the USA Option...

10

Drive train, fuel, suspension, steering & brakes / Re: Power Steering Leak

« Last post by acbrock on June 02, 2024, 21:56:19 »

So started her up with the Reservoir open and bubbled and foamed up like crazy.  So heading to Ace to get a 1/4Tube.  So this is probably stupid question but I Put the tube on the nipple and the unscrew the nut on the nipple?  Or is there another part I need to unscrew to get it to Bleed?