Pagoda SL Group

W113 Pagoda SL Group => Drive train, fuel, suspension, steering & brakes => Topic started by: County Guy on February 28, 2019, 23:36:18

Title: What parts do I need to buy to replace the front crank shaft seal 230sl
Post by: County Guy on February 28, 2019, 23:36:18

Hi.  I want to replace the front crank shaft seal on my 230sl but I'm confused about what I need.  I have two numbers from Mercedes.

a 'collar spacer' : 108-031-02-51
a 'crank seal'  :  008-997-05-47

Are these parts correct?  Do I need any others?

Thanks for any help you can give.

Title: Re: What parts do I need to buy to replace the front crank shaft seal 230sl
Post by: Benz Dr. on February 28, 2019, 23:41:08

Probably correct numbers but I don't have my parts book in front of me. Look at your crank gear and if worn you might want to replace that too since everything is already off. That may require a bit more disassembly though. ;)

Title: Re: What parts do I need to buy to replace the front crank shaft seal 230sl
Post by: vintagecoupe on March 01, 2019, 09:13:07

Hi,
you might also want to check and replace the two dowel pins, that hold the counterweight in place at the front end of the crankshaft.
They cost very little and if you sit there on a sunday afternoon, ready for reassembly without them....

Andreas

Title: Re: What parts do I need to buy to replace the front crank shaft seal 230sl
Post by: wwheeler on March 01, 2019, 17:35:25

Pins aren't a bad idea. Mine were buggered up a bit from a previous PO when I went to put it back together. Even with brand new pins, I had to LIGHTLY file (with the emphasis on lightly) the pins to get the counterweight on with a snug fit. Mostly on the ends for a very slight starting taper. It took many trial fits before it was right. I just didn't want to smash it on like it was done before.

Most importantly, and has been said before, the counterweight only goes on one way. But it is so close it is easy to do it wrong. Be sure to index before you take it off. You will sleep better at night.

Title: Re: What parts do I need to buy to replace the front crank shaft seal 230sl
Post by: Naj ✝︎ on March 04, 2019, 12:29:12

Hi,

#58 Pin               N000007 008244
#108 Seal Ring  008 997 0447
#200 Seal Ring  001 997 1241

naj

Title: Re: What parts do I need to buy to replace the front crank shaft seal 230sl
Post by: Vander on March 04, 2019, 20:33:05

Were you able to find the crank spacer? I am having trouble locating one.

Title: Re: What parts do I need to buy to replace the front crank shaft seal 230sl
Post by: Tom in seattle on March 05, 2019, 20:26:50

I had trouble with the dowel pins also, I recommend replacing them.

Title: Re: What parts do I need to buy to replace the front crank shaft seal 230sl
Post by: MikeSimon on March 05, 2019, 23:17:59

Stupid question:

Can you replace the front seal without taking the crank out, i.e.: with engine still installed in car?

Title: Re: What parts do I need to buy to replace the front crank shaft seal 230sl
Post by: Vander on March 06, 2019, 00:02:37

Yes, you can do it with the engine in the car. Remove hood, radiator, and front engine components.

Title: Re: What parts do I need to buy to replace the front crank shaft seal 230sl
Post by: ja17 on March 06, 2019, 05:32:09

Not sure what books you have but (Early BBB 03-12/1,12/2 also Late BBB 03-2/1).  Info and part numbers.