Pagoda SL Group

W113 Pagoda SL Group => Body, interior, paint, chrome, and cosmetic items => Topic started by: Brandini on April 24, 2025, 00:23:01

Title: Heater valve linkage to flap
Post by: Brandini on April 24, 2025, 00:23:01

I am in the process of repairing my heater core and discovered that the linkage is missing from the heater core valve to the flap. I am going to purchase one from vintageeuroparts.com but they have multiple sizes. Does anyone know how long it's supposed to be? I realize they can be adjusted. 

Here are the sizes they have in stock:

1. 6" long
2. 9.5" long

- Brandon

Title: Re: Heater valve linkage to flap
Post by: dirkbalter on April 24, 2025, 03:37:55

This is what my linkage at the heater valve measured.

Title: Re: Heater valve linkage to flap
Post by: Brandini on April 26, 2025, 15:16:19

Quote from: dirkbalter on April 24, 2025, 03:37:55

This is what my linkage at the heater valve measured.

Thank you for this. I don't think the one Vintageeuroparts.com is correct as it looks different. 

Does anyone know where I can purchase a linkage for the heater flap like the one in the picture? Is there a part number I can search for?

Title: Re: Heater valve linkage to flap
Post by: DavidAPease on April 26, 2025, 19:05:48

Could you just buy one of the ones from VEP (assuming they're not crazy expensive), then cut down a piece of the correct threaded rod to the length Dirk shows?

             -David

Title: Re: Heater valve linkage to flap
Post by: Pawel66 on April 26, 2025, 21:48:11

I cannot find part number, I suppose it may be part of heat exchanger - it looks like it is just not there. If the ball joints are the same as in linkage, they are available. Rods are available too, question of cutting and threading them.

Title: Re: Heater valve linkage to flap
Post by: Fresnomike on April 27, 2025, 01:54:29

I just went through this, and I ended up buying the throttle linkage ball ends from Authentic Classics. I bought two right hand threaded ends, then I bought some 5mm all-thread and cut it to size.

Title: Re: Heater valve linkage to flap
Post by: Brandini on April 27, 2025, 02:29:21

Quote from: DavidAPease on April 26, 2025, 19:05:48

Could you just buy one of the ones from VEP (assuming they're not crazy expensive), then cut down a piece of the correct threaded rod to the length Dirk shows?

             -David

Thanks David...I found some on their website that is around $30. Still not cheap but should work once I cut it to the correct size.

Title: Re: Heater valve linkage to flap
Post by: Brandini on April 27, 2025, 02:31:00

Quote from: Fresnomike on April 27, 2025, 01:54:29

I just went through this, and I ended up buying the throttle linkage ball ends from Authentic Classics. I bought two right hand threaded ends, then I bought some 5mm all-thread and cut it to size.

This is also a good idea...thank you for the suggestion.

Title: Re: Heater valve linkage to flap
Post by: Pawel66 on April 27, 2025, 06:36:27

Throttle linkage ball ends at Mercedes are $7-8 item, please check A 000 993 04 61 at a dealer or classic center. They are available here in Europe, chances are they are also available in the US.

At SLS they are EUR 2.80, but then you would have duties and shipping.

Title: Re: Heater valve linkage to flap
Post by: Bshaunessy on April 27, 2025, 14:12:56

PIERCE MANIFOLDS located California (https://www.piercemanifolds.com) is a good source for fuel and heater system rods and ball connectors.   Good service as well.